Repairs And Restroration Product

CRETORE ZR COAT

CRETORE ZR COAT is a two component system based on metallic Zinc and Epoxy resin system
Type =Two pack cold cure
Application= Brush, roller, spray
Finish =Matt
Mixing Ratio =3:1 by Volume
Mixed density= Approx. 1.60 gm/cc
Pot Life : 6-8 Hrs @23ºC
2-4 Hrs @30ºC
Surface Drying time =10- 60 minutes @ 30°C
Tack free := 1-3 Hrs @ 30ºC
Hard Dry := 15-18 Hrs @ 30ºC
Scratch Hardness (IS-101)= 2 Kgs
Salt Spray:= 300 Hrs
Overcoat =16-24 hrs.
Application =rate for repair 6.5 sqm/kgs
For new surface by spray =6.5 to 12 sqm per liter
Application= Temp +10oC to +35oC

• Zinc rich system combats corrosion electrochemically
• Permanent protection to the steel structure
• Excellent adhesion and flexibility to steel
• Time Saving-touch dry after 35 to 40 Minutes
• Exhibits excellent bond strength in cementitious repair.

Uses:

• Used as a primer on reinforced bars for anticorrosive System and in concrete repairs Also, can be used on exterior surfaces as a coating of
• Machinery
• Fertilizers tanks
• Metal Structural girders
• Metal gate and railings

CRETORE RUST REMOVER

CRETORE RUST REMOVER is very effective product for removing mill scale and rust, besides removing thin films of oil and grease CRETORE RUST REMOVER is formulate dusing phosphoric acids and other chemicals
Appearance Yellowish colour liquid
Specific gravity@ 27ºC 1.28 gm /cc
pH @ 27ºC Approx 2
Concentration=25 litersforevery100ltrsof working volume. (The exact amount of water to be added to CRETORE RUST REMOVER should be arrived at by the Customer by experimentery as a small scale)
Free acidity points =28 - 32 points
Iron content tolerated= Below 1.5%
Operating Temperature= Ambient

Advantages:

• Simple application by brush.
• Effective rust removal, even from areas difficult to reach.
• Contains no chloride- no chance of further corrosion.
• Cost effective coverage

Uses:

• One bars during repairs to there in forced concrete structure Maintenance of mild steel structures like tanks water pipelines shuttering plates and other corroded steel surfaces

CRETORE RUST CONVERTOR

CRETORE RUST CONVERTOR is a rust treatment which stabilises and converts adamantly adhering rust in to a organo - complex compound, resulting in the formation of a non- porous and moisture - repelling coating of good mechanical stability, abrasion resistance, bond strength and excellent anti-corrosive properties
Appearance Reddish colour liquid
Specific gravity@ 27ºC 1.000 – 1.030
Duration of dip About 30 mins

Advantages:

• Good mechanical stability
• Abrasion resistance
• Bond strength
• Excellent anti-corrosive properties

Uses:

• Light Houses.
• Equipment generally exposed to serve atmosphere.
• Oil refineries.
• Chemical plant and petro chemical industries.
• Steel bridges steel work.
• Off shore and onshore equipments cranes.
• Marine equipments.
• Civic engineering, construction (Steel reinforcement rods.)
• Pipes & Steel structurals.
• Deck frames and Modules, Splash zones.
• Ship building, Ship repairing.
• Electricity and gas power stations.

CRETORE BOND AGENT

CRETORE BOND AGENT is a modified Styrene Butadiene Rubber emulsion specially designed for use as a mortar modifier for cementitious systems and a bonding aid.
Base Modified SBR emulsion
Color: Milky White
Specific Gravity: Approx.1.02 gm/cc

Advantages:

• Simple use & thin application is possible
• Single component,
• Provide excellent bond to concrete, adhesion plaster, masonry, stone work, etc.
• Weather resistant helps improved durability
• Impermeability to chloride and other harmful agents
• Provides water tight screeds, plasters
• Improves tensile, adhesion and flexural properties
• Compatible with all hydraulic cements
• Economical to use

Uses:

• Concrete repair and adhesive Mortar, screed
• Repair of worn damaged and spalled concrete
• Repair of large cracks
• Polymer modified Floor screeds
• Rendering smooth, good finish, water tight external plaster.
• Thin layer patching mortars
• Tile fixing mortars, Masonry Mortars

CRETORE CRACK FILL-GP

It is a cement based polymer modified powder material for filling cracks in plastered surfaces

Advantages:

• Adhesion - Strong adhesion to common building substrates.
• Easy to use
• Good water resistance properties & weathering durability
• Eco- friendly - Does not content solvent.
• Non shrink in nature

Uses:

• To fill the static cracks of 2 to 3 mm sizes
• To level the undulation of the un plastered or plastered ceilings and walls
• To provide smooth finish to brick and stone,

CRETORE CRACK FILL-WP

It is a cement based polymer modified powder material for filling cracks in plastered surfaces

Advantages:

• Adhesion - Strong adhesion to common building substrates.
• Easy to use
• Good water resistance properties & weathering durability
• Eco- friendly - Does not content solvent.
• Non shrink in nature

Uses:

• To fill the static cracks of 2 to 3 mm sizes
• To level the undulation of the un plastered or plastered ceilings and walls
• To provide smooth finish to brick and stone

CRETORE QUICK PLUG

CRETORE QUICK PLUG is chloride free quick setting cement with immediate start of hardening after addition of water.
Basis Cement, additives
Colour Cement grey
Bulk Density 1.2 gm/cc
Application
temperature + 50C to + 300C
Start of setting Immediately after water addition

Advantages:

• Instant arrest of the leakage area

Uses:

• Subsequent sealing of surface leakage, water leaks and damp areas in cellars, manholes, tunnels, etc.
• Against water and pressure water from the backside or front side.

CRETORE COAL TAR-EP

CRETORE COAL TAR-EP is Solvent free Epoxy Coal tar protective coating, having excellent chemical resistance to a wide range of chemical
Base =Pale yellow colored liquid
Hardener= Black color thick liquid.
Mixed Color =Black
Mix Density:= Approx.1.15 gm/cc
Pot life @ 20°C= 30 minutes
@ 30°C =15 minutes
Time between coats@30°C= 8-12 hrs
Surface drying time @30°C =Approx.8-12
Initial Hardness @30°C= 24 hrs.
Full cure= 7 day
Application Temperature Min: +5°C, Max: +42°C
Service temperature Min: -10°C, Max: +45°C

Advantages:

• Solvent free
• Excellent adhesion to wide range of substrate like, concrete, steel etc.
• Chemical resistance – Resistant to wide range of acids, alkali & salt solutions, effluents & sewage.
• Can be applied for both above ground as well as underground structures
• Easy to apply

Uses:

• Protection to steel & concrete structures
• Soils for granular chemicals.
• Protective coating for underground concrete structure and bridges.
• Under-side of motor vehicle chassis.
• Protection of concrete from water vapor transmission Permeability & chemical system.
• Recommended for Sewage treatment plants & ETP

CRETORE REPAIR MORTAR

CRETORE REPAIR MORTAR is a polymer-modified, shrinkage compensated mortar. For interior and exterior use without corroding substances. Good process ability of the flexible, pasty and stable mortar
Basis =Cemented mortar
Colour= Grey
Bulk density= 1.5 kg/dm3
Water powder ratio =0.15 to 0.16
Fresh weight density =Approx. 2.10 gm/cc
Compressive strength
@ 27°C (ASTM C109)
1 day Minimum 10 N/mm2
28 day Minimum 25 N/mm2

Advantages:

• Easy to use (only to be mixed with water)
• Good adhesion
• Suitable for hand and machine application

Uses:

• For repair work of ruptures and defects in walls and ceiling made of concrete and precast concrete.
• For the preparation of concave mouldings.

CRETORE STONE SHIELD-S

CRETORE STONE SHIELD-S is a ready to use solvent based colorless water repellent.
Base Solvent Base
Color Water White
Specific Gravity 0.9 gm/ml

Advantages:

• Low Molecular Weight
• High penetration
• Reduction of capillary water absorption
• Reduces efflorescence
• Reduces dirt penetration into the pores
• Can be over coated with solvent based and dispersion coating
• Does usually not change the appearance of the substrate.
• Reduces chloride ion ingress and movement.
• Does not act as a vapour barrier
• Applicable on slightly moist surfaces Quick formation of a water-repellent effect therefore fast pelting rain proof

Uses:

• CRETORE STONE SHIELD-S is recommended for facades, inclined, vertical areas to arrest ingress of moisture.
• Excellent: for porous concrete, bricks, lime sand stone, mineral paint
• Good: Concrete cement bonded artificial stone, asbestos cement
• Different: Natural Stone

CRETORE STONE SHIELD-W

CRETORE STONE SHIELD-W water Repellent is a water diluted solution of alkali alkyl silicon ate designed to impart water repellency to a wide variety of surfaces
Specific gravity at 25°C 1.04 - 1.06
pH Approx 13

Advantages:

• Leaves the interior dry in all weather conditions
• Prevents fungus and moss growth
• Good penetration capacity
• long lasting and durable impregnation to facades
• Nonflammable

Uses:

• For moisture protection of facades or for inclined areas
• Porous concrete, bricks, lime sand stone
• Clinker Facades Stones, Light concrete etc.

CRETORE CRACK FILL-AP

CRETORE CRACK FILL -AP is composed of high quality weather durable acrylic emulsion polymer based, single pack, ready to use flexible putty for filling the cracks in plastered surfaces.
Appearance= Smooth & thick paste .Colour off White
Density= at 30°C 1.45 ± 0.1
Consistency= Viscous paste
Non volatile content= Approx 72+/-2 %
Tack free time at 230C =Approx 30 minutes
Vertical slumpin= MM Nil
Water resistance= Excellent
Extension recovery =Approx 60 %
Freeze / thaw stability, 5 cycles =Passes
Volume shrinkage-= Approx 22 %
Movement accommodation factor= Approx +10 % at 270C
Application temperature= Min: +5°C, Max: +42°C
Service temperature= Min: -10°C, Max: +45°C

Advantages:

• Consistency - Paste form, without sagging.
• Ease of application – Easy to apply by putty knife similar to conventional putties.
• Flexibility - Flexible, therefore does not crack &accommodates minor movements in cracks.
• VOC - Water based with very low voc hence ecofriendly.
• Paint ability - Over coat able by any type of polymer based paints, after 24 hours.
• Staining - Non-staining.
• Bonding - Excellent adhesion with cementitious surface.
• Durability – Excellent resistance to UV & atmospheric conditions.
• Toxicity - Non toxic & harmless to hands.

Uses:

• Internal & external plastered brick masonry wall cracks (max. up to 5 mm width crack.)

CRETORE MICRO CONCRETE

CRETORE MICRO-CONCRETE is ready to use single component dry powder cementitious material
Fresh wet density @27ºC 2150 - 2250 kg/m³
Expansion characteristics Unrestrained expansion 1 to 4%
Compressive strength (in N/mm²) (The following results were obtained at water Powder ratio of 0.18 @ 300C). (Tested on 70.6mm cubes as per BS 4551-80) 1 Day 10 N/mm² 3 Days 20 N/mm²
7 Days 30 N/mm²
28 Days 40 N/mm²
Flexural strength @ 28 days 3.5 N/mm²
Tensile strength @ 28 days 3 N/mm²

Advantages:

• Can be pumped or poured into restricted locations.
• Highly fluid to allow for placement without vibration.
• Pre-packed for better result on site.
• Low permeability
• Economical
• Contains no chloride.
• Ease of use

Uses:

• Structural strengthening measures such as filling honeycombs and cracks.
• Strengthening of vertical columns
• It is mainly recommended for the repair of damaged concrete structures, columns beams, slabs etc. it is also recommended for grouting of large gaps.